News / Blog| admin |
| Mill router based on myCNC control from our collegues. |
| 2012.02.17 03:35:10 | |
|
Our collegues from Belgium (Flander Motion bvba) use myCNC control for their 3 axes mill router.
Tags: cnc machines | myCNC control Hits: 30 | Read more... |
| admin |
| Jogging with analogue joysticks is available now on myCNC control software. |
| 2012.02.06 12:46:10 | |
|
2 or 3 axes analogue joystick can be connected through ADC channels of myCNC-ET1 controller and programmed for pendant panel jog motion. Motion speed is smoothly regulated with about 1% accuracy. We are working also on MPG (Manual pulse generator) support for myCNC software. Tags: myCNC software | myCNC-ET1 Ethernet CNC controller Hits: 48 | Read more... |
| admin |
| Plasma power source based on myPlasma control is ready for experiments. |
| 2012.02.06 12:40:24 | |
 Tags: myPlasma | plasma cutting plasma power source Hits: 57 | Read more... |
| admin |
| Fanuc-style Macro programming: G65 code implementation. |
| 2011.12.07 12:12:58 | |
|
We are working on G65 code implementation which allow to work with parameterized macros. G65 code runs macro program with number, programmed in P parameter. In a screenshot is shown peck drilling cycle (G83) repeated in a line by running G65 with macro O9911.
Listing of nc program is below: %
Tags: myCNC software Hits: 290 | Read more... |
| admin |
| Canned cycles implementation. |
| 2011.11.30 11:46:48 | |
|
We have started canned cycles implementation in myCNC. In the last version (1.72) codes C80, G83, G98, G99 are available. Hope rest of cannedcodes should become available during a couple of weeks.The last version is available on download page
Tags: myCNC software Hits: 149 | Read more... |
| admin |
| G68/G69 codes works now with planes codes G17,G18,G19 |
| 2011.11.24 11:20:11 | |
|
G68/G69 codes works now with planes codes G17,G18,G19 for myCNC software. (Described features will be available in myCNC control software version 1.72) Rotation coordinates codes G68-G69 may be used now with planes codes G17-G19 to rotate coordinates in any of planes XY, XZ, YZ. On a picture below there is a sample of using G68/G69 codes with G17-G19 plane selection. Also in the sample was used parameterized programming and M98/M99 subroutines (subprograms).
NC codes for the sample is listed below- G90G0X0Y0Z0#200=100 (size) #201=2 (delta angle) #202=360/#201 (number of lines) (XY plane) #100=0 #101=0 #102=#200 #103=#200 #104=0 #105=#200 G0 X#100 Y#101 Z#102 G17 M98 P101 L#202 (XZ plane) #100=0 #101=#200 #102=0 #103=#200 #104=#200 #105=0 G0 X#100 Y#101 Z#102 G18 M98 P101 L#202 (YZ plane) #100=#200 #101=0 #102=0 #103=#200 #104=#200 #105=0 G0 X#100 Y#101 Z#102 G19 M98 P101 L#202 o101 G68 X#100 Y#101 Z#102 R#110 G1 X#103 Y#104 Z#105 G1 X#100 Y#101 Z#102 G69 #110=#110+#201 M99
Tags: myCNC software | G codes programming Hits: 177 | Read more... |
| admin |
| Automatic gas console implementation through PLC layer of myCNC-ET1 controller. |
| 2011.11.21 12:37:13 | |
|
Great sample of using built-in PLC controller is implementation of Automatic gas console control for oxyfuel gas metal cutting. Gases pressure for fuel, preheat and cutting oxygene controlled electronically by 3 PID controllers, integrated in myCNC-ET1.
Tags: Automatic gas console | myCNC control Hits: 196 | Read more... |
| admin |
| myCNC software version 1.72 coming soon. G17,G18,G19 codes are implemented. |
| 2011.11.21 12:20:24 | |
|
myCNC software version 1.72 coming soon. G17,G18,G19 codes are implemented.
nc codes sample is listed below: G90G0X0Y0Z0
Tags: myCNC software Hits: 157 | Read more... |
| admin |
| myCNC based mill machine demo. |
| 2011.11.21 12:10:58 | |
|
This is our 3 axes mill machine based on myCNC (myCNC-ET1 LAN CNC controller, myCNC software, 4x myServo-A01 servo drivers).
Tags: cnc machines Hits: 196 | Read more... |
| admin |
| Experiments with surface measure and alu cut on our cnc mill prototype. |
| 2011.11.03 11:50:38 | |
|
Surface measure procedure were repeated a few times to check stabilityof measures.
The first cut of aluminium on our mill machine prototype.
Tags: cnc machines Hits: 188 | Read more... |
| admin |
| New screen, optimized for big 17" touch screen display |
| 2011.09.21 11:10:59 | |
|
We've made new screen design, optimized for big 17" touch screen display
Tags: myCNC software Hits: 285 | Read more... |
| admin |
| myServo-A01 + 400W Servo Brushless DC motor - Jog control through Serial console. |
| 2011.09.20 13:02:07 | |
|
Firmware for Servo driver myServo-A01 was updated to have manual jog mode through serial console. Host PC connected to myServo driver through USB serial connection. In Jog mode there are available setup for Speed and Acceleration, Jog +, Jog - , Stop commands.
Tags: myServo-A01 | myCNC | hardware Hits: 346 | Read more... |
| admin |
| myServo-A01 + 400W Servo Brushless DC motor - Jog control through Serial console. |
| 2011.09.20 13:02:04 | |
|
Firmware for Servo driver myServo-A01 was updated to have manual jog mode through serial console. Host PC connected to myServo driver through USB serial connection. In Jog mode there are available setup Speed and Acceleration, Jog +, Jog - , Stop commands.
Tags: hardware | myCNC | myServo-A01 Hits: 310 | Read more... |
| admin |
| Test stand |
| 2011.09.10 05:15:00 | |
|
Test stand
Hits: 263 | Read more... |
(sorry for this)| admin |
| Support forum. |
| 2011.08.29 11:45:29 | |
|
We started forum for support myCNC products. If you have questions concerning myCNC controllers and software, you may ask it there. Address of forum - http://www.justcnc.com/forum/
Tags: myCNC support Hits: 270 | Read more... |
| admin |
| Fixed step jogging available in the myCNC software |
| 2011.06.16 10:26:36 | |
|
We've added fixed step jogging for precise positioning in myCNC control software. Step for jogging may be selected as 0.001, 0.01, 0.1, 1 mm/inch or can be flexibly given with L-param
The mode is under testing and will be available in the next version. Tags: myCNC software Hits: 423 | Read more... |
| admin |
| We have NURBS implementation in myCNC now. |
| 2011.06.09 06:29:47 | |
|
We have implemented NURBS (Non uniformed rational B-spline) in myCNC software and myCNC controllers. It worked now in test mode. G-codes G5.2 & G5.3 describe NURBS control points. myCNC control software decomposes NURBS to bezier spline curves and sends it to myCNC controller. Complete 3D spline interpolation iterration inside myCNC controller takes about 30us. With 80us of processing time it's about 40% of CPU time which is reliable for stable work. We have tested NURBS with Butterfly sample from EMC2.
Tags: myCNC control | myCNC software Hits: 479 | Read more... |
| admin |
| Documentation updated. New version of myCNC software available. |
| 2011.05.26 05:30:34 | |
|
There is available documentation for myTHC-RU01 Torch height controller and myServo-A01 servo driver on documentation page. Also new 1.53 version of myCNC software available on download page.
Tags: myCNC | myCNC software Hits: 600 | Read more... |
| admin |
| Documentation updated. |
| 2011.05.20 13:21:46 | |
|
User manuals for control boards myCNC-ET1 & myCNC-ET2 are available for download now on Documentation page Tags: myCNC control Hits: 410 | Read more... |
| admin |
| myPlasma announce. |
| 2011.04.14 13:59:26 | |
|
myPlasma coming soon. myPlasma is control system kit to build Plasma Power source, based on chopper IGBT technology (step-down converter). myPlasma kit includes:
Main features:
Tags: myPlasma | cnc machines Hits: 521 | Read more... |
